Mould maintenance is the difference between a tool that runs for years and one that fails early. A sensible programme combines preventive checks, clean storage and a written record; a fair warranty covers material and workmanship defects, not normal wear. Buyers who agree on both at the purchase stage avoid most after-sales disputes.
Why moulds fail: wear, corrosion, cooling and machine setting
Moulds fail for predictable reasons. Gates, cores and ejection areas wear as the tool runs. Cooling circuits scale or corrode if water quality is poor. Mechanisms seize when lubrication is neglected. And poor machine settings, such as excessive holding pressure or a mis-set ejector, can damage a sound tool in a short time.
Knowing the failure mode matters because each one needs a different response. Wear calls for replacement inserts or re-polishing. Corrosion calls for material or water-treatment changes. A mechanism failure calls for inspection and adjustment, not a blanket repair.
A preventive maintenance schedule by shot count
The most practical schedule is driven by the machine’s shot counter, with checks at defined production intervals and an inspection whenever part quality drifts. The exact interval depends on the resin, the part tolerance and how hard the mould is run, so it should be written for the specific tool rather than copied from a generic list.
A routine inspection typically looks at gate condition, cavity and core surfaces, ejector return, slider and lifter movement, cooling flow and leaks, and the condition of wear plates and guide pins. The findings go into the mould record, and the next interval is adjusted if wear is faster than expected.
Mould storage and preservation between production runs
Storage damages more moulds than buyers expect. A mould left with wet cooling lines, residual resin or no cavity protection can corrode between runs, especially in humid climates or after sea freight.
The minimum procedure is straightforward: clean the mould, dry the cooling circuits, protect the cavity and core with a suitable anti-rust agent, close on a stop block so the faces are not loaded, and store it dry and covered. A written procedure and a log of when it was last preserved turn this into a system rather than a habit.
What a mould warranty should actually cover
A warranty is only useful if it is specific. A fair one covers defects in materials and workmanship: a cracked plate, a mechanism that fails prematurely, a cooling leak caused by a manufacturing fault, or a dimension that was wrong from the start.
Good warranties also state what happens when a claim is made: who inspects, within what period, what evidence is needed and how repair is handled. A warranty that states no terms is not one the buyer can use. Our mould service page describes how service and support are organised after delivery.
Warranty exclusions buyers should check
Exclusions are where most disputes are born. Normal wear is almost always excluded, and so are misuse, running beyond the agreed process window, over-temperature, water corrosion and resins that were not declared at the design stage.
Other exclusions to check include damage in transit after handover, unauthorised modifications, and using the mould on a machine outside the agreed tonnage or platen size. None of these are unreasonable, but they must be written down. The buyer should read the exclusion list before signing, not after a failure.
Spare parts, inserts and repair lead time
A mould is easier to maintain when its wear parts are standard or documented. Ejector pins, springs, seals, gate inserts and locating elements should appear on a spare-parts list with enough information to reorder.
Ask at the quotation stage which parts are considered consumable, whether spares are supplied with the tool, and how replacements are sourced later. A mould with documented spares can be repaired locally in many cases, which reduces downtime even when the original supplier is far away. The mould tooling page shows the machining capability that supports repairs and insert replacement.
Records and traceability that make a claim possible
A warranty claim needs evidence. A mould record with the build date, steel grades, heat treatment, trial data, maintenance history and repair history makes it possible to establish whether a failure is a defect or wear.
Without records, every failure turns into a debate. The buyer’s own maintenance log matters too: what was run, at what settings, how the mould was stored and when it was last serviced. Our mould quality control page explains the inspection records created during build, which are the starting point for any later claim.
When repair is cheaper than a new mould
Repair is usually the better route when the damage is local: a worn gate insert, a damaged slider, a scored core or a failed ejection component. Replacing those parts can restore the tool at a fraction of the cost of a new mould.
A new mould makes more sense when the base is distorted, the cavity geometry is worn beyond tolerance across the whole tool, or the part design has changed enough that the old tool cannot follow. The decision should be based on an inspection and a repair report, not on a single failed part.
Frequently asked questions
How often should an injection mould be serviced?
The interval depends on shot count, resin, part tolerance and how the mould is run. A practical schedule is based on the machine’s shot counter with checks at defined production intervals, plus an inspection whenever quality drifts. The supplier should state the recommended checks in writing rather than leave the buyer to guess.
What does a typical mould warranty cover?
A fair warranty covers defects in materials and workmanship: a plate that cracks, a mechanism that fails prematurely, a cooling leak caused by a manufacturing fault, or a dimension that was wrong from the start. It should not cover normal wear, misuse, over-temperature running or corrosive resins that were not declared.
Are wear parts like ejector pins covered by warranty?
Usually not, because they are designed to be replaced. Ejector pins, springs, seals, gate inserts and similar items are consumables in a working mould. The right expectation is a spare-parts list, a source for replacements and a clear statement of which parts are covered and which are not.
How should moulds be stored between production runs?
Clean the mould, dry the cooling circuits, protect the cavity and core with a suitable anti-rust agent, close the mould on a stop block and store it in a dry place. Plastic parts and moisture are the main enemies of a stored mould. A short written storage procedure prevents most idle-time corrosion.
Can SinoMould repair a mould made by another supplier?
In many cases yes. The work starts with an inspection and a repair report: what failed, what can be repaired, what should be replaced and what the repair will cost. A mould from another maker can be maintained or modified, provided the drawings or the actual geometry can be measured and documented.
Ask for our mould service and spare parts list
Send the mould specification, part history and a description of the issue to [export@sinomould.com](mailto:export@sinomould.com), or contact SinoMould for a maintenance and repair assessment. With 20+ years of mould making, nearly 40,000 moulds delivered and ISO-certified quality management, SinoMould supports moulds through documented service, spare parts and global after-sales.
Warranty terms, service intervals and spare-parts arrangements vary by contract. Agree them in writing with your supplier before the mould is built.
Related mould guides
Continue with the next step of the mould project: