Buying a custom injection mould is a five-stage process: define the part and volume, brief the makers, compare quotations on specification, audit the factory, and protect the tool after delivery. Most problems come from skipping a stage, especially briefing and contract terms. A good buying process is less about finding the lowest number and more about knowing exactly what that number includes.
Define the part and volume before you ask for quotes
A mould quotation is only as good as the brief behind it. Before contacting suppliers, define the part, the resin, the annual volume, the target markets, the surface and colour requirements, the packaging and any machine constraints at the destination plant.
Volume matters most because it drives cavity count, which drives mould size and price. A part expected to run for several years at high volume justifies a different tool from a short programme with uncertain demand. Write the assumptions down; they become the basis for comparing quotations.
What to send a mould maker: drawings, resin, samples, volumes
Send a STEP or IGES file, a 2D drawing for tolerances and critical features, the resin grade, the annual and monthly volume, the cavity count you prefer and any existing mould or machine limits. Samples or photos help, but they do not replace a dimensioned file.
Also state what is not negotiable: a visible gate mark, a texture reference, a colour match, a packaging requirement or a certification the part must meet. Suppliers quote what they understand. Missing requirements are usually discovered at the trial, when changes cost money.
How to read and compare two mould quotations
Two quotations can only be compared line by line. The table below is a practical comparison sheet:
| Item to compare | What to record |
|---|---|
| Cavity count and layout | Number of cavities and the arrangement |
| Steel grades and hardness | Cavity, core, inserts, sliders |
| Mould base | Size, material and standard |
| Runner system | Cold runner, hot runner type, gate type |
| Cooling design | Circuit layout and fittings |
| Trial scope | What is included and what counts as a trial |
| Spare parts | What is supplied and what is consumable |
| Documents | Drawings, trial report, dimensional data |
| Packing and freight | Export packing, insurance, destination terms |
When the rows are filled, the difference between two quotations usually becomes obvious. A lower total with a smaller base, softer steel or no spare parts is not the same product. Our mould quality control page explains the inspection and documentation that should accompany that specification.
Auditing a mould factory: what to check on the floor
A factory audit answers questions a website cannot. Check the machine list against the mould sizes you need, the metrology equipment, the condition and organisation of the assembly area, and how steel and standard parts are stored and traced.
Ask how a trial is run, what the report contains and who approves it. Ask to see a mould record for a recent project, with the steel certificates and dimensional data. And talk to the engineers who would handle your tool. The mould tooling page lists the equipment classes to look for; a supplier should be able to show them in use.
Contract terms that matter: payment, ownership, warranty
Contract terms decide what happens when something goes wrong. The essential clauses cover payment stages, delivery terms, mould ownership, drawing and data ownership, warranty scope, spare-parts supply and the process for changes after design approval.
Payment should be tied to milestones the buyer can verify, such as design approval, trial sample approval and shipment readiness. Ownership and documents should transfer with the final payment. Warranty wording should separate material and workmanship defects from normal wear, as described in our mould maintenance guide. Certification claims can be checked against the honours and certifications page.
Tooling ownership transfer and mould relocation
A mould is an asset that should be movable. That requires documents, spare parts, a condition report and a clean handover. If the tool is to be moved later, the buyer should already hold the drawings, the 3D data and the trial records.
Relocation also needs a plan for the destination machine: tonnage, platen size, ejector pattern, cooling connections and hot runner controller compatibility. A tool that fits the maker’s machine may not fit the buyer’s. Planning the move at purchase time avoids surprises later.
Importing moulds: shipping, customs and documentation
International mould purchase adds logistics to the technical work. The tool needs export packing, usually a wooden case with rust protection, and the shipment needs an invoice, packing list and the customs documents required by both countries.
Before shipment, confirm what the buyer must do at arrival: unloading, inspection, installation, water and power connections and a first-article approval run. Our custom plastic mould overview explains the range of tools involved; the contact page is the place to raise specific shipping and documentation questions.
Red flags in a mould quotation
Some quotation patterns deserve a second look. A price far below the others, a single-line quotation with no specification, and a promise that every requirement is included without discussion are common warning signs. So is reluctance to provide steel certificates, trial reports or a spare-parts list.
A supplier who cannot explain how the cavity count was chosen, which steel will be used and what happens at the trial is not ready to build a tool. None of these signals is proof of a bad supplier, but each one is a reason to ask a direct question before paying a deposit.
Frequently asked questions
How do I choose an injection mould supplier in China?
Start with the part and the volume, then compare suppliers on process rather than on price alone. Look for a documented DFM and design review, a quality system, trial reporting, a spare-parts list and clear contract terms on ownership and warranty. Visiting or video-auditing the factory is the fastest way to confirm what a website claims.
What documents should a mould quotation include?
A usable quotation names the cavity count, steel grades and hardness, mould base size, runner type, cooling concept, trial scope, spare parts, packing and the documents delivered with the tool. If a quotation is one line of text, it is a budget indication rather than a specification.
Who owns the mould after I pay for it?
Ownership should be written in the contract and normally transfers to the buyer when payment is complete. The same clause should cover the mould drawings, 3D data and any electrodes or fixtures. Clarify it before the tool is built, because moving a mould later is much harder if ownership and documents are unclear.
What should I check during a factory audit?
Check the machine list against the mould sizes you need, the metrology equipment, the condition of the assembly area, how steel and standard parts are stored and traced, the trial process and the quality records. Talk to the engineers who will work on your tool, not only to sales.
How do I move a mould to another factory?
The mould must be complete, documented and packed for transport, with drawings, trial data, spare parts and a condition report. Ownership and handover terms should already be in the contract. Then arrange export packing, shipping and insurance, and plan a first-article approval run at the new plant.
Talk to a mould engineer
Send your part file, resin, volume and destination to [export@sinomould.com](mailto:export@sinomould.com), or contact SinoMould for a specification-level quotation and a factory audit by video or in person. With 20+ years of mould making, nearly 40,000 moulds delivered and ISO-certified quality management, SinoMould works with OEMs and brand owners on tooling that is documented, movable and supported after delivery.
Contract, shipping and warranty terms vary by country and project. Confirm them with your legal and logistics advisers before signing.
Related mould guides
Continue with the next step of the mould project: