An IML mould combines forming and decoration in one cycle: a printed label is placed in the cavity and bonds to the part as the plastic fills. That removes a separate printing step, produces a durable decorated surface and keeps the container in a single material, which matters for recycling. Designing an IML mould means designing the label interface, the placement method, the robot and the cooling as one system.

What IML is and where it pays off

In-mould labelling places a pre-printed label or film in the mould cavity before injection. The melt bonds the label to the part surface, so the decoration becomes part of the product rather than a separate sleeve or sticker.

It pays off where decoration is part of the product value and volume is high enough to automate: dairy cups, ice-cream containers, food tubs, lids, paint pails and promotional packaging. The label resists moisture and handling better than a glued label, and the part remains a single-material item that is easier to recycle.

Label types: paper, film, PP and the mould interface

Labels are not all the same, and the mould must suit the one that will be used. Paper labels, PP film and multi-layer laminates differ in stiffness, curl, thickness and how they bond to the resin. A label designed for a flat surface behaves differently on a curved cup wall.

The mould interface follows the label: the label pocket depth, the edge radius and the venting all affect how the label sits and how air escapes. A label that traps air produces bubbles; a label that sits too loosely shifts during filling. The label and the cavity are a matched pair. Our packaging mould overview shows how these packaging tools are grouped.

Static, vacuum and air-assist label placement

Labels can be held in the cavity by static charge, by vacuum through small ports in the cavity, or by air assistance that presses the label against the surface. Each method has practical consequences.

Static is simple but can be affected by humidity and label material. Vacuum gives positive holding but needs ports, a vacuum circuit and maintenance access; the ports must not leave visible marks. Air assist helps on large or curved labels where a simple pocket is not enough. The choice belongs in the mould design, not in the robot commissioning.

Designing the mould around the robot and label magazine

An IML mould does not work alone. A robot takes the label from a magazine, places it in the cavity, and later removes the finished part. The mould design must give that robot room, repeatability and a defined pick-and-place position.

That means clearance for the end effector, sensor positions to confirm the label is present, and a layout that lets the robot reach every cavity without collisions. Designing the tool first and adding automation later usually produces a slower, less reliable line. The technical highlights page covers the process capability behind this kind of integration.

Cup, container and lid IML: different requirements

Although the principle is the same, the three product families stress the mould differently:

Product type Main mould consideration
Cups Curved label pocket, wall stiffness, stacking rim
Containers and tubs Flat or slightly tapered walls, label edge and base radius
Lids Thin section, label registration, stacking and sealing features
Buckets and pails Large label area, handle and lid interface, IML with thicker walls

A cup mould focuses on roundness and rim strength. A lid mould focuses on flatness and thin-wall filling. A bucket mould, such as those used for paint and coatings, focuses on a large decorated area and the strength needed for filling and transport. Our IML paint bucket mould work is an example of the larger end of that range.

IML with thin wall: cycle time and stiffness trade-offs

Thin-wall containers are where IML becomes technically demanding. The wall is already thin, and the label adds a layer that must bond without distorting the part. The gate position, the label pocket and the cooling must be designed together.

Faster cycles help the economics, but a thin wall with a label needs care: uneven cooling can warp the label area, and a poorly supported label can wrinkle. The thin-wall food container mould page describes the tooling approach for these parts. The practical answer is to design the label zone with the same discipline as the wall itself.

In-mould labelling quality checks

Quality checks for IML go beyond dimensions. The label must be correctly positioned, fully bonded, free of bubbles and wrinkles, and consistent in colour and gloss. The edge of the label should sit cleanly against the plastic, with no lifting or flash over the print.

In production, a first-off check confirms placement and bonding, and periodic checks catch drift. Trial samples should be checked against the label artwork and the agreed appearance standard, not only against the part drawing. A trial that proves the mould but not the label is not finished.

Matching mould, machine and automation

An IML mould is one part of a production cell: mould, machine, robot, label magazine, conveyor and quality check. The cell works when the cycle time of each element matches, and the mould is usually the hardest element to change later.

That is why the specification stage matters. Cavity count, label size, robot reach, magazine capacity and cooling all interact. SinoMould designs and builds the mould against the customer’s automation plan, and supports the trial with documented process settings so the cell can be reproduced at the destination plant.

Frequently asked questions

What is the difference between IML and IMD?

IML (in-mould labelling) places a printed label or film into the cavity and bonds it to the part during moulding. IMD (in-mould decoration) uses a printed film that becomes part of the surface, often for deeper graphics or durable decorative panels. Both use the mould as the forming and bonding tool, but the film construction, part design and mould interface differ.

Can any injection mould be converted to IML?

Not directly. IML needs label location, vacuum or static assistance, sensor positions and robot clearance designed into the tool. Some existing moulds can be modified for IML, but the work is a redesign of the label interface rather than a bolt-on. The conversion should be assessed against the part and the required cycle.

Which label placement method suits high-cavity cups?

High-cavity cup moulds usually need a reliable, repeatable placement method, so vacuum or static assistance is planned together with the robot and the label magazine. The right choice depends on the label material, the cavity layout and the cycle time. The mould, robot and label feed are designed as one system.

Does IML work with thin-wall containers?

Yes, IML is common on thin-wall containers, cups and lids. The challenge is that the label and the wall compete for the same space, so the wall section, the label pocket and the gate position must be designed together. Cooling and cycle time also need more attention than in a plain thin-wall tool.

What do you need to quote an IML mould?

Send the part file, the label specification (material, thickness, print side and finish), the required cavity count, the robot or automation plan and the annual volume. A label sample or artwork is useful because the label edge, curl and print registration affect the mould design.

Send your container and label spec

Share the part file, label specification, automation plan and annual volume with [export@sinomould.com](mailto:export@sinomould.com), or contact SinoMould for an IML mould quotation. With 20+ years of mould making, nearly 40,000 moulds delivered and ISO-certified quality management, SinoMould designs IML tooling together with the automation interface, then supports trial and mass production with global after-sales.

Label materials, robots and automation layouts vary by project. Confirm the exact label and cell specification with your supplier before the mould design is frozen.

Related mould guides

Continue with the next step of the mould project: