A hot runner mould keeps the melt hot from the machine nozzle to each cavity gate, so no runner solidifies and no runner scrap is produced. The design decisions that matter most are manifold layout, gate type, temperature control and the maintenance plan. Valve gates give positive shut-off and a clean gate; thermal gates are simpler and often enough at lower cavity counts. The right choice follows volume, resin and appearance.
What a hot runner changes: cycle time, scrap and gate quality
A hot runner changes three things at once. It removes the cold runner, so there is no runner scrap to regrind and no degating step. It shortens the cycle in many tools because there is less material to cool. And it changes the gate: the melt stays fluid to the cavity, so the gate mark, the fill balance and the shut-off behaviour become design variables.
Those benefits are real but not free. The manifold, nozzles, heaters, thermocouples and controller add cost and add maintenance points. A hot runner is a system, and its reliability depends on how well it is integrated into the tool.
Manifold layout and balanced flow
The manifold distributes melt from the machine nozzle to each cavity. A balanced layout gives every cavity the same flow length, pressure drop and residence time, so parts fill consistently across the tool.
Unbalanced layouts show up as cavity-to-cavity weight differences, overpacked cavities near the inlet and short shots at the far end. The layout must also avoid dead spots where material can sit and degrade, and it must leave room for heaters, thermocouples and wiring that can actually be serviced.
Valve gate versus thermal gate: when each wins
A valve gate uses a pin to open and close each gate positively. That gives a clean gate mark, independent shut-off and good control of packing, at the cost of pins, actuators, wear parts and more maintenance.
A thermal gate relies on the melt freezing at the gate tip between shots. It is simpler, cheaper and needs less hardware, but the gate mark is less controlled and very small gates can freeze inconsistently.
The decision usually follows cavity count and appearance. High-cavity caps and closures, where every gate mark and every part weight must match, tend toward valve gates. Simpler parts at lower cavity counts often run well on thermal gates.
Temperature control zones, controllers and wiring
A hot runner works only if the temperature is controlled zone by zone. Each nozzle and manifold section needs its own heater and thermocouple circuit, sized so it can recover quickly after each shot.
The mould design must accommodate the wiring: routes, connectors, strain relief and a controller position that suits the machine. A good thermal design with poor wiring access becomes a maintenance problem. The mould R&D overview describes how process and tooling engineering work together on these systems.
Gate vestige, colour change and material constraints
Gate vestige is the small mark left at the gate. Its size and appearance depend on the gate type, the resin and the part design. For visible parts, the acceptable vestige should be agreed before the mould is built, because it is difficult to change afterwards without reworking the gate.
Colour changes and material changes put a hot runner under stress. Dead spots trap the previous colour, and long flow paths take longer to purge. Materials with fillers or high processing temperatures need a runner system rated for them. These constraints belong in the runner specification, not in a commissioning conversation.
Hot runner maintenance and spare parts
A hot runner is the most maintenance-intensive part of many moulds. Heaters, thermocouples, nozzle tips and valve pins wear or fail, and manifold leaks can damage the tool if they are not caught early.
A maintenance plan should include periodic checks of heater and thermocouple performance, nozzle condition and valve movement, plus cleaning when colour changes demand it. The system should be handed over with a wiring diagram, a spare-parts list and the controller settings. Our technical highlights page covers the inspection and process discipline behind these tools.
When a cold runner is the better choice
A cold runner is often the better decision. Short production runs may never recover the extra cost of a hot runner. Heat-sensitive resins can degrade in a manifold. Colour changes that must be fast and clean are simpler with a cold runner. And some parts can use the runner itself as a handle or a sprue that is part of the product.
The comparison should be made on total cost: tool price, scrap, cycle time, labour for degating and the value of the runner material if it can be reground. The page on injection mould cost explains how to structure that comparison, and the preform mould page shows a product family where hot runner design is central.
Specifying a hot runner in your mould enquiry
A useful hot runner enquiry states the part, the resin, the annual volume, the cavity count, the gate type you expect, the acceptable gate mark, the colour-change frequency and any existing controller or spare-parts standard in your plant. Those inputs let the mould maker propose a runner system that fits the tool and the factory.
Without them, the supplier guesses, and the guess shows up at the trial. The best time to agree the runner is before the mould design is released, when the manifold layout can still be changed cheaply.
Frequently asked questions
Is a hot runner worth the extra mould cost?
It depends on volume, resin and appearance. A hot runner adds manifold, nozzles and temperature control, so the mould costs more. It earns that back through lower runner scrap, shorter cycles and less manual degating when the volume is high enough. At low volume the savings may never cover the extra tooling.
Valve gate or thermal gate for a 32-cavity cap mould?
A 32-cavity cap mould usually benefits from positive gate shut-off, because gate appearance and part weight consistency matter across all cavities. Valve gates add cost and maintenance but give better control of the gate mark and fill balance. The final choice should follow the cap design, resin and cycle target.
Can you work with a hot runner brand we already use?
Yes, in most projects the manifold and nozzle system can be specified to match the buyer’s existing standard, so spare parts and controllers stay compatible across a plant. The mould design then integrates that system rather than replacing it. The interface details should be agreed before the mould design is released.
How do you handle colour changes in a hot runner mould?
Colour changes are planned into the manifold layout: dead spots are avoided, flow paths are kept short and smooth, and gate shut-off is used where it helps purging. Some systems are easier to clean than others, so colour-change frequency should be stated when the runner is selected, not discovered after delivery.
What maintenance does a hot runner need?
A hot runner needs periodic checks of heater and thermocouple performance, nozzle tip condition, manifold leaks and wiring, plus cleaning when colour or material changes demand it. The system should be documented with a spare-parts list and wiring diagram so maintenance can be planned rather than reactive.
Send your cavity layout and resin
Share the part file, resin, cavity layout and volume with [export@sinomould.com](mailto:export@sinomould.com), or contact SinoMould and ask for a gate type recommendation before the tool is quoted. With 20+ years of mould making, a 70,000 m² manufacturing base and ISO-certified quality management, SinoMould designs hot runner moulds as complete systems, including manifold layout, temperature control, documentation and global after-sales support.
Runner systems, gate types and controller standards vary by project. Confirm the exact specification with your supplier before the mould design is approved.
Related mould guides
Continue with the next step of the mould project: