Injection mould cost is driven by six main factors: cavity count, steel grade and mould base, hot runner choice, part size and complexity, surface finish, and the engineering and trial work behind the tool. For the same part, a single-cavity P20 mould and a hardened multi-cavity hot runner mould are different products with different prices. That is why a quotation without a stated specification cannot be compared with another quotation.

What an injection mould price actually covers

A custom mould is a small engineering project, not a single catalogue item. The price is the sum of design and DFM, steel and mould base, machining hours, standard parts, runner system, trial and correction, project management, packing and freight. Each line behaves differently when the part or volume changes. Two quotations can look far apart and still describe the same scope at different assumptions, so ask for each line separately.

Cavity count: the biggest cost lever

Cavity count is the largest lever because it multiplies work across the whole tool: more inserts, a larger mould base, a longer runner layout, more cooling circuits and a bigger machine to run it.

The economic logic is simple. A higher-cavity mould costs more to build, but it spreads that cost over more parts per cycle, so the cost per part falls as annual volume rises. A low-cavity mould is cheaper to buy and faster to build, and suits modest volumes, large heavy parts, or designs that may still change. Cavity count is a volume decision, not a default preference. Our mould cost estimation system shows how part data and cavity choice interact before a formal quote.

Steel grade and mould base: P20, 718H, H13, S136

Steel is the second big lever, and the most common place for a quotation to be quietly reduced. P20 and 718H are pre-hardened grades used for large, low-wear parts such as crates, pallets and appliance housings. H13 and 1.2344 are hot work steels for high-volume tools and abrasive resins. S136 and 2316 are stainless grades for medical parts, PVC and clear components where corrosion or polishing quality matters.

Steel alone does not make a good mould. Heat treatment, mould base rigidity, cooling design and machining accuracy matter just as much. Our mould tooling capability covers the machining and inspection side of that equation.

Hot runner vs cold runner: cost and running trade-offs

A hot runner keeps melt hot in the manifold and nozzles until it reaches each cavity. It adds a manifold, nozzles, a temperature controller and extra wiring and machining, so the mould price is normally higher.

The payback comes from running cost. A hot runner removes runner scrap, shortens the cycle, reduces manual degating and makes multi-cavity balancing easier. At high volume those savings can outweigh the extra tool cost; at low volume they usually do not. Cold runners remain a good choice for short runs, heat-sensitive resins, fast colour changes and parts where the runner can be reground.

Part size and complexity: slides, lifters and unscrewing

Part size drives mould size, steel weight, machining time, lifting requirements and machine tonnage. Complexity is the other half: every undercut, thread, side hole or reverse draft needs a mechanism such as a slider, lifter, collapsible core or unscrewing device. Each mechanism adds design time, machining, fitting, trial risk and maintenance points.

SinoMould runs a 70,000 m² manufacturing base with five-axis CNC, mirror EDM and CMM inspection, so demanding geometry is machined and verified in-house.

Surface finish, texture and IML requirements

Cosmetic requirements change the mould price more than many buyers expect. A high-gloss surface needs steel that polishes well, careful polishing and protection during handling. A textured surface needs consistent etch depth and a steel grade that holds the texture.

In-mould labelling (IML) adds another layer: label placement, vacuum or static assistance, sensors and robot clearance must be designed into the mould. State the finish standard, texture reference and any IML plan at quotation stage. The plastics material guide explains how resin choice interacts with finish and steel.

How to compare two mould quotations side by side

Comparing quotations is mostly a discipline problem. Line up the same questions and the differences become visible:

Question to ask Why it matters
What cavity count and layout is quoted? Sets output per cycle and the machine required
Which cavity, core and insert steels, at what hardness? The main long-term durability variable
Which hot runner brand and gate type? A major share of tool cost and cycle performance
How many trials are included, and what is a trial? A trial can be a dry run or full dimensional approval
What spare parts, drawings and records come with the tool? Affects maintenance and future repairs
What is included in packing, shipping and documentation? Often the hidden gap between two totals

A supplier who will not itemise these points is not necessarily expensive, but the comparison is not finished. Our automatic quotation system is useful for a first range, while a firm mould quotation should always arrive with a named specification.

Why a cheap mould gets expensive later

A low mould price is not automatically a good deal. The cost usually reappears somewhere: lower-grade steel that wears faster, a smaller base that flexes, a cheap hot runner with poor temperature control, skipped trials, or no documentation and spare parts. The expensive version of a low-cost mould shows up as longer cycles, more scrap, downtime and frequent repairs.

The better question is not “which mould costs least” but “which mould has the specification my volume needs”. That usually means the correct cavity count, steel matched to resin and volume, a runner system chosen on total cost, and enough trial work to prove the tool before shipment.

Frequently asked questions

How much does a custom injection mould cost?

There is no single figure, because a mould is quoted against a specification. Cavity count, steel grade, runner type, part size and finish decide most of the price. The same part quoted as a single-cavity P20 tool or as a hardened multi-cavity hot runner tool is two different products, so compare quotations only after the specification behind each one is clear.

Why is cavity count the largest cost driver?

Cavity count multiplies the core and cavity work, the mould base size, the runner system and the tonnage needed to run the tool. Moving from one cavity to a high-cavity layout can cut the cost per part sharply, but the tool itself becomes larger and more expensive, so the right choice depends on annual volume.

Does a hot runner always increase mould cost?

A hot runner adds a manifold, nozzles, controllers and more wiring and machining, so the tool price usually rises. It can still lower total cost at high volume by removing runner scrap, shortening cycles and reducing manual degating. At low volume, or with heat-sensitive resins, a cold runner is often the more sensible choice.

What part data do you need to quote a mould?

Send a 3D file (STEP or IGES) or a detailed 2D drawing, the resin, the annual volume, the cavity count you prefer, the surface requirements and any existing mould or machine constraints. A weight and a photo are useful for a first discussion but not enough for an itemised quote.

Why do two quotations for the same part differ so much?

Quotations usually differ in steel grade, mould base size, hot runner brand, cavity count, cooling design, trial allowance, spare parts and what the supplier assumes in the fine print. Two numbers cannot be compared until those specifications are lined up.

Request a mould quote

Send your 3D file, resin and annual volume to [export@sinomould.com](mailto:export@sinomould.com), or contact the SinoMould team. A tooling engineer will review the part and return an itemised mould quotation covering design, steel, runner system, trials and documentation. With 20+ years of mould making, nearly 40,000 moulds delivered and ISO-certified quality management, SinoMould supports projects from DFM through mass production and global after-sales.

This guide uses general industry ranges, not a quotation for your part; your cost depends on the agreed specification.

Related mould guides

Continue with the next step of the mould project: